Are you handy? - Page 4

Squid_Operator · 07-21-2007, 03:52 AM

Handy?

Hitting a bound girl with it? noo.........

Wait what?...

bluecuracao · 07-21-2007, 04:16 AM

Well, it sure looks functional.

Squid_Operator · 07-21-2007, 04:18 AM

Crude should be a synonym for functional.

SteveDallas · 07-21-2007, 07:40 AM

Wait, you use this to keep the squids in line?

xoxoxoBruce · 07-21-2007, 08:21 AM

Quote:

Originally Posted by bluecuracao

Okay, that's the problem--you're worried about the way it's going to look, which I can understand in your line of work. In the case of a roof, it has to be very functional and long-wearing, i.e. tight and sealed.

A long piece of roll roofing is not like fabric, it's like a wide, thin board. It can roll and flex, and it can twist, but it can't change it's rectangular shape, unless it's very, very hot. Rolled out flat, it has to be straight... like the edge of the roof. The only way you can make it crooked, is to cut it up in a bunch of short pieces.

If the top layer (straight), and the bottom layer (not straight), don't match, being cemented it will seal out wind driven water and ice damns. But it will make a weaker edge that will deteriorate much faster.

The edges can be made to match, using care, with either method. But using a single piece is faster and easier.

Squid_Operator · 07-21-2007, 03:28 PM

R U SQUIDDIN'!!?? I know I'm Squiddin'!

DucksNuts · 07-21-2007, 11:25 PM

I seriously....groaned out loud....GOL I guess?

glatt · 07-23-2007, 01:18 PM

The pictures of my project would be much less interesting than BigV's, so I won't be posting any.

Over the weekend, I installed a bathroom vent fan in a small bathroom that had none before.

This meant:

1. Putting a new circuit breaker into an empty slot in the panel, running the romex to the 1st floor bathroom wall where I installed a GFCI receptacle and a switch (had to fish the wire for this part,) then running it back down into the basement and up the open wall where I'll be re-tiling a shower and into the open ceiling above that gutted shower. The fan will be GFCI protected.

2. Pulling out the ladder and cutting a hole in the second story exterior wall for the vent hood. Caulk around the hole, slide the hood in, and screw it tight.

3. Crawling around in the hot very cramped nasty eaves to get the flexible ductwork installed and nice and straight. This was a major pain, as a bunch of loose fill insulation had fallen down into the eaves from the attic and I didn't want to stir it up too much. I got a nasty cramp in one leg while I was all contorted trying to tighten up the clamp holding the duct to the hood.

4. Install the fan between the ceiling joists, connect the ductwork to the fan. This actually took a fair amount of time as I had to shim the joists to account for the new drywall ceiling I'll need to install.

5. Wire up the fan to the romex I installed earlier.

6. Try to act all nonchalant when the damn thing worked on the first test.

7. Clean up.

wolf · 07-23-2007, 01:22 PM

I am crafty, but not handy, unless you count being able to substitute a bunch of linked paperclips for the ball chain that's in the toilet tank ...

Clodfobble · 07-23-2007, 03:47 PM

Sure, you guys install roofs and air vents and crap, but I creatively reattached Barbie's legs while retaining functionality.

Flint · 07-23-2007, 03:53 PM

Quote:

Originally Posted by Clodfobble

...I creatively reattached Barbie's legs while retaining functionality.

I used to make Transformers out of Legos. The three-way kind, IE plane/tank/robot.

Happy Monkey · 07-23-2007, 04:43 PM

I had a ton of house parts, so I made Transformers that became houses. Sucks to be them.

I also made little Gobot-types out of paper, and I still have a couple of them.

As for the original question, I've put a soap tray back into the shower wall after I knocked it out, but I'm leery of anything major. I'm not sure what percentage of that leery is laziness, though.

yesman065 · 07-23-2007, 04:58 PM

Quote:

Originally Posted by wolf

I am crafty, but not handy, unless you count being able to substitute a bunch of linked paperclips for the ball chain that's in the toilet tank ...

Watch out they rust pretty quickly - been there done that.

bluecuracao · 07-23-2007, 05:04 PM

Quote:

Originally Posted by Clodfobble

Sure, you guys install roofs and air vents and crap, but I creatively reattached Barbie's legs while retaining functionality.

How did you do that??!

Clodfobble · 07-23-2007, 05:29 PM

Rubber bands, a little dexterity, and a lot of patience.

07-23-2007, 01:22 PM	#54
wolf lobber of scimitars Join Date: Jul 2001 Location: Phila Burbs Posts: 20,774	I am crafty, but not handy, unless you count being able to substitute a bunch of linked paperclips for the ball chain that's in the toilet tank ... __________________ wolf eht htiw og "Conspiracies are the norm, not the exception." --G. Edward Griffin The Creature from Jekyll Island High Priestess of the Church of the Whale Penis

07-23-2007, 04:43 PM	#57
Happy Monkey I think this line's mostly filler. Join Date: Jan 2003 Location: DC Posts: 13,575	I had a ton of house parts, so I made Transformers that became houses. Sucks to be them. I also made little Gobot-types out of paper, and I still have a couple of them. As for the original question, I've put a soap tray back into the shower wall after I knocked it out, but I'm leery of anything major. I'm not sure what percentage of that leery is laziness, though. __________________ _________________ \|...............\| We live in the nick of times. \| Len 17, Wid 3 \| \|_______________\| [pics]

07-21-2007, 03:52 AM	#46
Squid_Operator [Radio Operator] Join Date: Jul 2007 Location: [Hawaii/Monterey california] Posts: 43	Handy? Hitting a bound girl with it? noo......... Wait what?...

07-21-2007, 04:16 AM	#47
bluecuracao in a mood, not cupcake Join Date: Jun 2005 Location: Philadelphia Posts: 3,034	Well, it sure looks functional.

07-21-2007, 04:18 AM	#48
Squid_Operator [Radio Operator] Join Date: Jul 2007 Location: [Hawaii/Monterey california] Posts: 43	Crude should be a synonym for functional.

07-21-2007, 07:40 AM	#49
SteveDallas Your Bartender Join Date: Jan 2002 Location: Philly Burbs, PA Posts: 7,651	Wait, you use this to keep the squids in line?

07-21-2007, 03:28 PM	#51
Squid_Operator [Radio Operator] Join Date: Jul 2007 Location: [Hawaii/Monterey california] Posts: 43	R U SQUIDDIN'!!?? I know I'm Squiddin'!

07-21-2007, 11:25 PM	#52
DucksNuts Bitchy Little Brat Join Date: Sep 2005 Location: Queensland, Australia Posts: 5,067	I seriously....groaned out loud....GOL I guess?

07-23-2007, 01:18 PM	#53
glatt ™ Join Date: Jul 2003 Location: Arlington, VA Posts: 27,717	The pictures of my project would be much less interesting than BigV's, so I won't be posting any. Over the weekend, I installed a bathroom vent fan in a small bathroom that had none before. This meant: 1. Putting a new circuit breaker into an empty slot in the panel, running the romex to the 1st floor bathroom wall where I installed a GFCI receptacle and a switch (had to fish the wire for this part,) then running it back down into the basement and up the open wall where I'll be re-tiling a shower and into the open ceiling above that gutted shower. The fan will be GFCI protected. 2. Pulling out the ladder and cutting a hole in the second story exterior wall for the vent hood. Caulk around the hole, slide the hood in, and screw it tight. 3. Crawling around in the hot very cramped nasty eaves to get the flexible ductwork installed and nice and straight. This was a major pain, as a bunch of loose fill insulation had fallen down into the eaves from the attic and I didn't want to stir it up too much. I got a nasty cramp in one leg while I was all contorted trying to tighten up the clamp holding the duct to the hood. 4. Install the fan between the ceiling joists, connect the ductwork to the fan. This actually took a fair amount of time as I had to shim the joists to account for the new drywall ceiling I'll need to install. 5. Wire up the fan to the romex I installed earlier. 6. Try to act all nonchalant when the damn thing worked on the first test. 7. Clean up.

07-23-2007, 03:47 PM	#55
Clodfobble UNDER CONDITIONAL MITIGATION Join Date: Mar 2004 Location: Austin, TX Posts: 20,012	Sure, you guys install roofs and air vents and crap, but I creatively reattached Barbie's legs while retaining functionality.

07-23-2007, 05:29 PM	#60
Clodfobble UNDER CONDITIONAL MITIGATION Join Date: Mar 2004 Location: Austin, TX Posts: 20,012	Rubber bands, a little dexterity, and a lot of patience.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)