a photoblog of what i did today..... - Page 10

plthijinx · 02-14-2011, 09:18 PM

.

glatt · 02-15-2011, 10:38 AM

Looking good.

Question: Those cut up vertical pieces seem to be supported only by the connection to the existing drywall and a little cantilevered action from that stud to the side. I don't really get it. Are they just something to hold the drywall/hardi screws for the new wall? Or are they supported by something solid that I can't see?

footfootfoot · 02-15-2011, 10:55 AM

ahhh. I got to go take a nap right now...

plthijinx · 02-15-2011, 01:22 PM

yyyyeah. i don;t agree with this part of the installation. he needs to notch 2x4s (my apostrophe key doesn;work sometimes and i;m tired of pounding the shit out of it) and put it in there. i asked him about this and i got a mumble answer. errr one i cant remember right now. doesnt make sense to me either. not a load bearer so whatev......

glatt · 02-15-2011, 02:35 PM

Yeah, I'm sure it's fine. Not the way I'd do it, but the house isn't going to fall down or anything.

plthijinx · 02-15-2011, 04:40 PM

Quote:

Originally Posted by glatt

Yeah, I'm sure it's fine. Not the way I'd do it, but the house isn't going to fall down or anything.

actually it is a load wall now that i looked at it again but one stud isn;t going to make that much of a difference. but like you said glatt, the house isn;t going to fall down.

plthijinx · 02-15-2011, 04:50 PM

ok time to do some electrical work. remember to always make sure the circuit is off then verify using a voltage tester. most know this but the black wire is your HOT wire and the white one is the neutral. the bare wire is the ground wire, or sometimes it;s green. oh, and when you do test the circuit you should have somewhere in the neighborhood of 120 volts. on this circuit i have 121 but that;s alright.

after striping back the insulation on the wires you then twist them together. black to black white to white ground to ground then use wire nuts on the hot and neutral. it;s always good practice to then seal up the wire nut with electrical tape.

sorry for the somewhat fuzzy pictures. my crackberry is overdosing today.....

plthijinx · 02-15-2011, 05:01 PM

the cut outs for the fart fan and a/c duct were a tad off but will be alright because of the flanges on the vent covers. then in the back there is the shower light. the fart fan is on it;s own circuit because i did not want the fan to suck up steam from the shower since it;s not venting to anywhere but the ceiling. i know i know....i tried to tell him. vent to outside but eh.....anyway.

the garage let alone the house is a disaster area right now. here is the new vanity that we are installing. picked it up on what ladies?? yes, we picked it up....on sale!

$100 bucks.

plthijinx · 02-15-2011, 05:01 PM

.

plthijinx · 02-15-2011, 05:33 PM

ugh....back at it. i can hear paul cussing in canadian all the way up here in my bedroom.

Shawnee123 · 02-16-2011, 09:01 AM

Quote:

Originally Posted by plthijinx

ugh....back at it. i can hear paul cussing in canadian all the way up here in my bedroom.

What's that all aboot?

plthijinx · 02-16-2011, 08:51 PM

Quote:

Originally Posted by Shawnee123

What's that all aboot?

it;s aboot pronunciation.

Quote:

"ahhhh facker! get in there ya whore! oh fack aff!"

he was trying to screw in sheetrock and kept missing the stud.
*snicker*

omg! kitty been in a fight with the clippers!!

Quote:

Originally Posted by clodfobble

The noble apostropholon returns!

indeed. i have to pound the crap out of that key to get it to work. lemme count here.....

' oh. sure. right. damn thing worked the first time. beh. gonna go grab pics of what we did this morning before i had to drive to work to do more decking.....

zippyt · 02-15-2011, 06:55 PM

cussing in canadian

Ehh FUCK !!!

plthijinx · 02-15-2011, 06:59 PM

lmao yep! and the "awww you mother fucker, you piece of shit, get in there, ahhhh fuck all eh"

edit: now i'm saying that too. smashed my thumb with the hammer.

fargon · 02-16-2011, 11:29 AM

This is what we did to Kung Pao Kitty yesterday.

02-14-2011, 09:18 PM	#1
plthijinx Master Dwellar Join Date: Aug 2003 Posts: 4,197	. Attached Images __________________ For your dreams to come true, you must first have a dream.

02-15-2011, 10:38 AM	#2
glatt ™ Join Date: Jul 2003 Location: Arlington, VA Posts: 27,717	Looking good. Question: Those cut up vertical pieces seem to be supported only by the connection to the existing drywall and a little cantilevered action from that stud to the side. I don't really get it. Are they just something to hold the drywall/hardi screws for the new wall? Or are they supported by something solid that I can't see? Attached Images

02-15-2011, 10:55 AM	#3
footfootfoot To shreds, you say? Join Date: Aug 2004 Location: in the house and on the street-how many, many feet we meet! Posts: 18,449	ahhh. I got to go take a nap right now... __________________ The internet is a hateful stew of vomit you can never take completely seriously. - Her Fobs

02-15-2011, 01:22 PM	#4
plthijinx Master Dwellar Join Date: Aug 2003 Posts: 4,197	yyyyeah. i don;t agree with this part of the installation. he needs to notch 2x4s (my apostrophe key doesn;work sometimes and i;m tired of pounding the shit out of it) and put it in there. i asked him about this and i got a mumble answer. errr one i cant remember right now. doesnt make sense to me either. not a load bearer so whatev...... __________________ For your dreams to come true, you must first have a dream.

02-15-2011, 04:50 PM	#7
plthijinx Master Dwellar Join Date: Aug 2003 Posts: 4,197	ok time to do some electrical work. remember to always make sure the circuit is off then verify using a voltage tester. most know this but the black wire is your HOT wire and the white one is the neutral. the bare wire is the ground wire, or sometimes it;s green. oh, and when you do test the circuit you should have somewhere in the neighborhood of 120 volts. on this circuit i have 121 but that;s alright. after striping back the insulation on the wires you then twist them together. black to black white to white ground to ground then use wire nuts on the hot and neutral. it;s always good practice to then seal up the wire nut with electrical tape. sorry for the somewhat fuzzy pictures. my crackberry is overdosing today..... Attached Images __________________ For your dreams to come true, you must first have a dream.

02-15-2011, 02:35 PM	#5
glatt ™ Join Date: Jul 2003 Location: Arlington, VA Posts: 27,717	Yeah, I'm sure it's fine. Not the way I'd do it, but the house isn't going to fall down or anything.

02-15-2011, 05:01 PM	#8
plthijinx Master Dwellar Join Date: Aug 2003 Posts: 4,197	the cut outs for the fart fan and a/c duct were a tad off but will be alright because of the flanges on the vent covers. then in the back there is the shower light. the fart fan is on it;s own circuit because i did not want the fan to suck up steam from the shower since it;s not venting to anywhere but the ceiling. i know i know....i tried to tell him. vent to outside but eh.....anyway. the garage let alone the house is a disaster area right now. here is the new vanity that we are installing. picked it up on what ladies?? yes, we picked it up....on sale! $100 bucks. Attached Images __________________ For your dreams to come true, you must first have a dream.

02-15-2011, 05:33 PM	#10
plthijinx Master Dwellar Join Date: Aug 2003 Posts: 4,197	ugh....back at it. i can hear paul cussing in canadian all the way up here in my bedroom. __________________ For your dreams to come true, you must first have a dream.

02-15-2011, 06:55 PM	#13
zippyt LONG LIVE KING ZIPPY! per Feetz Join Date: Mar 2003 Location: Arkansas Posts: 7,661	cussing in canadian Ehh FUCK !!! __________________ "Success is getting what you want. Happiness is wanting what you get. " Brother Dave Gardner

02-15-2011, 06:59 PM	#14
plthijinx Master Dwellar Join Date: Aug 2003 Posts: 4,197	lmao yep! and the "awww you mother fucker, you piece of shit, get in there, ahhhh fuck all eh" edit: now i'm saying that too. smashed my thumb with the hammer. __________________ For your dreams to come true, you must first have a dream. Last edited by plthijinx; 02-15-2011 at 07:32 PM.

02-16-2011, 11:29 AM	#15
fargon Person who doesn't update the user title Join Date: Dec 2005 Location: La Crosse, WI Posts: 8,924	This is what we did to Kung Pao Kitty yesterday. Attached Images __________________ Annoy the ones that ignore you!!! I live a blessed life I Love my Country, I Fear the Government!!! Heavily medicated for the good of mankind.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode